- How do you connect a subwoofer to an amplifier?
- How do you connect a subwoofer to an amplifier? | HowStuffWorks
Get your capacitor as close to the amp as possible, and use the same ground as you did for the amp.
Have your power wire taunt and find out where your cap. You cannot just plug it in; you must charge it first with a resistor, use a 1k ohm resistor because they do not get as hot, it only takes a few seconds to charge, do not do this bare handed. You want to ground your cap. Run the power wire to your amp. If you have a stock stereo and you have the remote wire there you want to in twine the remote wire with the power wire before inserting in the power slot for amp.
- How do you connect a subwoofer to an amplifier??
- online dating valentines day.
- How do you connect a subwoofer to an amplifier?.
- .
The remote wire tells the amp to turn on. Make sure you always turn off your amp when you leave your car, it will overheat and drain your battery. Turn the gain all the way down, start playing music and turn it up to where you usually listen, where the mids sound good. Tune them gain until the subs sound good.
RMS is very important when matching subs and amps, yes not enough power will make subs clip, but also to much power will burn your voice coils by over heating them with too much power. Subs and amps should be matched as closely as possible for best performance and longevity. I have a Pioneer deck, amp, and kicker, installed to shut off from the battery.
The sub cuts on and off at high volume when I use the auxiliary cord to phone. How do I fix this? That could mean your amp cannot handle the sub. Another important factor to consider is Ohms. If you have a 2 ohm sub and a 4 ohm amp it won't produce enough power to properly power the sub. Not Helpful 2 Helpful The wires are not grounded properly, check to make sure the surface is clean, unpainted metal. Not Helpful 6 Helpful Not Helpful 5 Helpful What would cause my sub to kick in when radio is on and stop working when I change source to CD?
The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna. Remove the wire and find the correct remote amp, then turn on wire or ignition wire to the vehicle. Not Helpful 15 Helpful You should be able to connect it to the auxiliary on the back of the stereo unit. Not Helpful 3 Helpful 7.
My amp is already installed and I just bought a new sub. How do I connect my new sub to my old amp? There should be RCA female plugs on your amp, and on the new sub-box enclosure, there should be another set of RCA plugs or clamps. Just match the positive and negatives. Not Helpful 14 Helpful Remote; connect the REM wire to a fuse that only has power when the car is on. I cannot turn it up any higher than halfway without my amp going into protective mode.
What would cause this? This could be caused by a bad ground. Run yourself a good wire for ground directly to the chassis. Not Helpful 1 Helpful 3. What if I bought my radio harness to fit my truck only? Will the wires still match up on the aftermarket radio I purchased? It will just plug into your truck and then connect color coordinated wires. Not Helpful 0 Helpful 1. How should I connect the remote wire so that I don't have to disconnect it when I turn off the car? Hook it to a fuse connected to ignition turn on, like your accessory power fuse.
Not Helpful 16 Helpful What do I do if my amp comes on with static through my speakers when I turn on the key, but nothing else comes through?
Answer this question Flag as Where do you get lock nuts for the power and ground wires on my amp? Can I run 4 speakers and a subwoofer from a single amplifier? Can I hook up a loc to the rear speaker wires if there is a factory amp to them? If not, where do I hook up the loc wires? Can you add subs to a factory radio? Subs and amps should be matched as closely as possible for best performance and longevity. I have a Pioneer deck, amp, and kicker, installed to shut off from the battery. The sub cuts on and off at high volume when I use the auxiliary cord to phone. How do I fix this?
That could mean your amp cannot handle the sub. Another important factor to consider is Ohms. If you have a 2 ohm sub and a 4 ohm amp it won't produce enough power to properly power the sub. Not Helpful 2 Helpful The wires are not grounded properly, check to make sure the surface is clean, unpainted metal. Not Helpful 6 Helpful Not Helpful 5 Helpful What would cause my sub to kick in when radio is on and stop working when I change source to CD?
The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna. Remove the wire and find the correct remote amp, then turn on wire or ignition wire to the vehicle. Not Helpful 15 Helpful You should be able to connect it to the auxiliary on the back of the stereo unit. Not Helpful 3 Helpful 7. My amp is already installed and I just bought a new sub.
How do I connect my new sub to my old amp? There should be RCA female plugs on your amp, and on the new sub-box enclosure, there should be another set of RCA plugs or clamps. Just match the positive and negatives. Not Helpful 14 Helpful Remote; connect the REM wire to a fuse that only has power when the car is on.
I cannot turn it up any higher than halfway without my amp going into protective mode. What would cause this? This could be caused by a bad ground. Run yourself a good wire for ground directly to the chassis. Not Helpful 1 Helpful 3.
How do you connect a subwoofer to an amplifier?
What if I bought my radio harness to fit my truck only? Will the wires still match up on the aftermarket radio I purchased? It will just plug into your truck and then connect color coordinated wires. Not Helpful 0 Helpful 1. How should I connect the remote wire so that I don't have to disconnect it when I turn off the car?
Hook it to a fuse connected to ignition turn on, like your accessory power fuse. Not Helpful 16 Helpful What do I do if my amp comes on with static through my speakers when I turn on the key, but nothing else comes through? Answer this question Flag as Where do you get lock nuts for the power and ground wires on my amp? Can I run 4 speakers and a subwoofer from a single amplifier?
- dating divas couple photos;
- dating apps ireland.
- 2020 dating apps!
- How to Wire an Amp to a Sub and Head Unit: 12 Steps.
Can I hook up a loc to the rear speaker wires if there is a factory amp to them? If not, where do I hook up the loc wires? Can you add subs to a factory radio? If so short simple easy way? And how can you test your subs to see if there working. Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. Tips Don't forget to test your rem wire before you assume it works.
How do you connect a subwoofer to an amplifier? | HowStuffWorks
Last thing you need is a dead battery. If your amp doesn't turn on, check the amp fuses. When connecting a line out connector to a factory head unit, it is advisable to use both sets of speaker wires to maintain the left and right stereo effect from modern music. Always remember to shut off the amp if you do so manually Soldering 12v power and ground connectors to the wires will reduce circuit resistance and make your power cleaner, giving you better sound.
Make sure that you use cables with the correct resistance or impedance for your setup. A bridged amp runs at a different impedance than the same amp in unabridged mode.